人妻无码久久中文字幕专区,中文有码无码人妻在线

站內搜索

新聞資訊

公司新聞行業動態

熱點

自動上料平口攪拌機多種方量可供選擇

2022-12-23

混凝土自動上料攪拌車的功能有哪些？

2022-12-19

混凝土自動拌料車移動式可自行走戶外施工

2022-12-16

自上料攪拌車企業這么多，買車的時候應該看哪方面？

2022-12-12

關于山汽

聯系人：劉老師

電話：400-879-1999

公司：山東山汽工程機械（集團）有限公司

地址：山東省萊州市206國道與308省道交叉口東南50米

自動攪拌一體車的堵塞的具體疏通步驟

所屬分類：公司新聞發布時間：2021-03-05 來源：http://m.842233.cn/ 瀏覽量：0

在使用自動攪拌一體機的時候要注意疏通進料口，如果出現堵塞的問題，應該怎么去處理，具體的步驟又是什么呢？下面給大家詳細的介紹一下。

When using the automatic mixer, we should pay attention to dredge the feed port. If there is a problem of blockage, how to deal with it, and what are the specific steps? Let's give you a detailed introduction.

今天我們會為大家?guī)頂嚢柢嚨那逑匆c，希望通過我們的介紹讓您對問題有更深入的了解

Today, we will bring you the key points of mixer cleaning. We hope that through our introduction, you can have a deeper understanding of the problem

由于混凝土會在短時間內凝固成硬塊，且對鋼材和油漆有一定的腐蝕性，所以每次使用混凝土貯罐后，洗凈粘附在混凝土貯罐及進出料口上的混凝土是每日維護必須認真進行的工作。其中包括：

As the concrete will solidify into hard lumps in a short time and corrode the steel and paint to a certain extent, it is necessary to clean the concrete adhering to the concrete storage tank and the inlet and outlet after each use of the concrete storage tank. These include:

1．每次裝料前用水沖洗進料口，使進料口在裝料時保持濕潤；

1. Flush the inlet with water before each loading to keep the inlet moist during loading;

2．在裝料的同時向隨車自帶的清洗用水水箱中注滿水；

2. At the same time of loading, fill the cleaning water tank with water;

3．裝料后沖洗進料口，洗凈進料口附近殘留的混凝土；

3. Wash the inlet after loading and clean the residual concrete near the inlet;

4．到工地卸料后，沖洗出料槽，然后向混凝土貯罐內加清洗用水30—40 L；在車輛回程時保持混凝土貯罐正向慢速轉動；

4. After unloading at the construction site, wash the discharge chute, and then add 30-40 l of cleaning water to the concrete storage tank; keep the concrete storage tank moving forward and slowly when the vehicle returns;

5．下次裝料前切記放掉混凝土貯罐內的污水；

5. Remember to discharge the sewage in the concrete storage tank before the next loading;

6．每天收工時徹底清洗混凝土貯罐及進出料口周圍自動，自動攪拌一體機的清洗要點保證不粘有水泥及混凝土結塊。

6. At the end of each day, thoroughly clean the concrete storage tank and the area around the inlet and outlet of the automatic mixer. The cleaning points of the automatic mixer are to ensure that there is no cement and concrete caking.

1、上下料時間參數不合理：自動上料機因料倉內無法加裝料位機，所以行業基本都有時間控制。如何設置時間參數，上下料時間設置其實很簡單，在初次使用時，先設置一個小的時候，然后根據每次吸料位置慢慢加，當達到料位達到吸料口的時間，再減去一秒就是合理時間。放料時間是確保放完料再加一秒。這樣做有兩個好處：一是料位太高對濾芯傷害特別大，二是每次料都能放干凈。

1. Unreasonable loading and unloading time parameters: automatic feeding machine can not be installed in the silo level machine, so the industry basically has time control. How to set the time parameter, loading and unloading time setting is actually very simple. In the first use, first set a small time, and then add slowly according to each suction position. When it reaches the material level and reaches the suction port, then subtract one second is the reasonable time. The discharging time is one second after discharging. This has two advantages: one is that the material level is too high, which will cause great damage to the filter element; the other is that the material can be put clean every time.

2、自動攪拌車進料口給料量是否合理：正確的方式是物料在吸料口和空氣形成一定的氣物混合比，在氣流的推動下均勻流入上料機。這個時候我們需要將料槍設計帶有補氣功能。如果物料積壓時間過長可能很硬，這個時候需要在料槍上裝一個振蕩器，敲碎結塊的物料。

2. Whether the feeding quantity of the automatic mixer is reasonable: the correct way is that the material forms a certain gas-solid mixture ratio at the suction port and the air, and flows into the feeder evenly under the push of the air flow. At this time, we need to design the material gun with air supply function. If the material overstocking time is too long, it may be very hard. At this time, an oscillator needs to be installed on the material gun to break the caked material.

上一頁：自動攪拌一體機戶外工作底盤損傷緊急修復方法? 下一頁：自動攪拌一體機的產品質量受哪些因素影響？

熱門產品 / HOT PRODUCT